Russel Brothers Limited   OWEN SOUND, ONTARIO   Steelcraft Boat Builders
HOME
Orville

Canadian List of Shipping. 1956: Orville [C.190240] registered at Port Arthur; built at Owen Sound In 1950. 15'5 x 8'1 x 4'5; 4- g.t.; 3 n.t.; 100 hp. Owned by Marathon Corporation of Canada Ltd., Toronto. Canadian List of Shipping 1970: Steel sloop Orville [C.190240] registered at Port Arthur. Built at Owen Sound in 1950 16' 4 g.t. Transport Canada List 2001: Orville [C.190240] owned by Purvis Marine Ltd., Sault Ste. Marie, Ontario. Transport Canada List 2002: Owned by Purvis Marine Ltd., Sault Ste. Marie. Built by Russel-Hipwell Engine Co., Owen Sound, Ont. GAO Notes: Reported by Purvis as sold in 2001. Transport Canada List 2002: Orwned by Purvis Marine Ltd., Sault Ste. Marie, ON.

 

Leigh Cossey supplied this photo posted by Richard Lamoreux on the Historic Northern Ontario FB page. From the collection of the Marathon and District Museum and Historical Society. Rail tie sawmill from Nipigon at Marathon wood yard. Orville is in left mid-ground, with un-named pilings harbour barge. Photo dated to between 1950 and 1952. Gord Campbell comments (Oct. 27, 2019): "As for dating the photo above.... Its definitely after 1950 since Orville was built in 1950. It looks like its before 1952 because I don't see any signs of either a chemical plant. Or a lime Kiln. The Marathon mill had the world's largest lime kiln in the Commonwealth when it was built.It had the most inefficient lime kiln in the Commonwealth."
ENLARGE TO 1000 PIXELS WIDE

 

ORVILLE in Marathon, Ontario, 1973. Awesome photo showing a tug boat (Orville) pushing and corralling logs into manageable booms in Marathon. Click on photo for enlarged view. Credit : Virtual Reference Library. Post to Historic Northern Ontario group by Don Yanisiew.
ENLARGE TO 1920 PIXELS WIDE

 

Graphic from defunct internet page by Gord Campbell of Marathon, Ont.: http://users.renegadeisp.com/geecee/orville.htm. Saved by Robert B. Farrow.
ENLARGE TO 1903 PIXELS WIDE

Orville. Dozer boat. Marathon Pulp Mill, div. James River Corp. circa 1983, Jellicoe Cove, Peninsula Harbour, Lake Superior. Operator/Cpt. Vince Poirier, Long Pole, Mickey. Relaxing during lunch break on Orville. Photo by G. Campbell, Black River Graphics

Gordon Campbell writes:

In the mid 1980's, I operated this boat. As one can see it was strenuous work. Relaxation between the long bouts of labour was important to maintaining a high level of the legendary productivity of Marathon employees. Here the senior commodore of the fleet, Vince Poirier consults with the crew leader, the Pond Leader, during the rare breaks in the constant action of driving wood. The photo from the collection of Vince Poirier, was likely taken circa 1980.

Orville was built circa 1951, mothballed circa 1985 and has been scrapped at the last report about circa 1997. It was one of the early type of dozer boats. It was built in a small shipyard near Owen Sound.

The boat could do about 14 knots at full power and threw a large wake due to the tubby hull shape. The boat was short with a length of about 14 feet. Beam was about 9' gunwhale to gunwhale. However it drew about 6 feet of water. In the picture there is as much steel below the waterline as above. The paint scheme as pictured here was originally yellow and grey, but later all orange was used.

Powered by a 4 cylinder, Cat Diesel which delivered about 130HP on the shaft depending on the condition of the engine and the environmental conditions the little boat shepherded the rafts of wood by pushing and position. It was keel cooled by water flowing in bladders in side the tugs hull. Navigation did not exist. It had one horn, one light, one trouble light, one pike pole, one fire extinguisher and the famous water bucket. It had two joined fuel tanks could last about eight days or 280 operating hours between bunkering.

There was one boat driver or operator per shift. Normal shifts during the season's height was three shifts, of eight hours for a five day week. The longest serving boat operator was Vince Poirier. Second longest was supposed to be a person by the name of Len Lavoie. Progression on the dewatering was feeder bridge, short pole, long pole. Promotion then split, the choice was to Raftsman, or to Pond Leader. Raftsman, who eventually aspired to Boat Driver, worked long pole and operated the Cancel for rafting purposes when required.

Orville on the beach in Marathon, Ontario c. 1983. Photo by Rob Marchand. (Photo cropped from the large panarama below).

While sluggish in straight line speed, Orville was extremely maneuverable. It could almost turn on its axis with a power burst. An accomplished operator could literally make the boat dance in the water doing whirls, twirls and figure eights. The job of the vessel was to yard and move wood into the pond of the jackladder. Loosening the rafts of floating wood, Orville guided seemingly endless rows of wood to the point where long pool men directed the floating wood into the wooden pond at the bottom of the jack ladder. The Jack Ladder was a huge chain ramp with rows of large steel chocks that lifted the wood in a hoped for orderly fashion from the cold waters of Lake Superior. The term was dewatering.

Orville was also the primary rafting boat in the pond. Its companion vessel was the Cancel which will be featured at a later date. As a result of being on Lake Superior and part of the Marathon Pulp Mill fleet with the flag vessel MDC Everest (command of Capt. George Matheson), Orville at one time was the smallest registered vessel and smallest tug on the Great Lakes. The second smallest was Cancel.

Hardworkers on the walkways of the pond would tug, pull and straighten the eight (8') foot lengths of wood into two organized rows lifted up to the saws. The two saws cut which cut the wood into four foot lengths for the debarking, sorting processes and later for chipping or wood storage.

The 8' standard was used in the woodlands to determine cordage in the field. The woodyard however was installed to process the 4' length. This resulted in an never ending dispute about just what was a cord of wood. To confuse the issue more. Chips were measured in tonnes and long tons as it enterred the mill process.

Since the statute of limitations is up, it was believed by the more knowledgeable workers that the company managers deliberately used the confusing numbers to artificially inflate the wood losses. Thereby the mill's owner/operators derived better tax positions, well, in other words paid much less tax. This postulation has since been confirmed by divers. According to the mill numbers there should be about 12 feet of wood on the bottom of the Peninsula Harbour and Jellicoe Cove were the numbers of losses accurate. One salvage company has taken a look at the commercial viability of wood salvage off the lakd bottom here and in the storage area at Port Monroe. Salvage operations never begun. There isn't all that much sunken wood.

Orville was named for the first Woodyard Superintendant, the late Orville MacKenzie. Orville MacKenzie was also my godfather. Strange that I was one of the last of the drivers aboard the boat. There was no job invented that I liked better than working on that vessel.

Marathon Woodyard and Pulp Mill c. 1983. Photo collage by Rob Marchand. enlarge to 2048 pixels wide.         enlarge to 16384 pixels wide.
https://www.flickr.com/photos/cuss/46974893241/in/album-72157704868439235/

Jan. 2018: Gord Campbell continues: It had a 120 hp 3cyl, Cummins diesel. The motor was a diesel tractor engine. In fact it sounded like a farm tractor. Its draft is equal to the length. Later dozer boats had a central steering yoke and the propeller unit that worked like today's Azipods. This one was the classic boat bow, motor. propeller shaft. Rudder steering with steering wheel.

Two reasons why it was scrapped... 1) Years of rubbing against wood logs had worn the hull paper thin. So thin it was possible to put the pick of a welding hammer through the hull. 2) The hull design was so deep and ungainly that it was very unsuitable for recreational or private use. It even had commercial limits. Its draft was so deep that we used Cancel for beachcombing.

 

For more Russel exhibits visit Owen Sound Marine & Rail Museum 1165 1st Ave West, Owen Sound, ON N4K 4K8
(519) 371-3333     http://marinerail.com